"Lug nuts must be torqued to the manufacturer’s recommended values, and they must be re-torqued to those values after driving approximately 50 to 100 miles on your new tires after the tire service."
They always over tighten all the nuts by as much as 200%
To guarantee they never loose never fell off. Lucky you if they don't warp your discs and you can loose any of the nut when you have a flat in the middle of the night in nowhere land.
Tighten all the nuts to specifiied torque while the car still on the lift, meaning there is zero weight applied to the wheels. So that the wheels are free to move close to position with the tightening force, that's how the factory does it. If you do it with the car on the ground you need a bigger force to push the wheels inwards. Think about pulling a paper under books vs without books on top of it.
with a typical 80 ftlb of torque I hope it's more than enough to overcome it.
Lug nut torque: 150 lb.ft (204 Nm) (M14 x 1.5). Torque specifications are for nut and bolt threads free of dirt and rust. Use only our recommended replacement wheel nuts and or wheel bolts. Re-torque requirement 2022 Ford Mustang Mach-E: Retighten the wheel nuts to the specified torque within 100 mi (160 km) after any wheel disturbance, such as flat tire repair, tire rotation, changing a flat tire or wheel removal.
有多少人真的在遵循做这些了？
"Lug nuts must be torqued to the manufacturer’s recommended values, and they must be re-torqued to those values after driving approximately 50 to 100 miles on your new tires after the tire service."
car dealership might take this seriously, I asked Acura dealership, they did do retorque, maybe not wait for a whole day
https://www.amazon.com/gp/product/B00C5ZL0RU
重装轱辘后的头100迈内有1/3的时候我发现过20个nuts中有两三个松了10到15度的样子。
原因是装上之后行车的颠簸会造成轱辘松动位移。
To guarantee they never loose never fell off. Lucky you if they don't warp your discs and you can loose any of the nut when you have a flat in the middle of the night in nowhere land.
What are you driving?
Mach e 轱辘的nut torque 要150ftlb,我还真没那手劲去拧。
the car is so heavy on the ground, I guess the tire ifself shifting position a bit when do torque,
Tighten all the nuts to specifiied torque while the car still on the lift, meaning there is zero weight applied to the wheels. So that the wheels are free to move close to position with the tightening force, that's how the factory does it. If you do it with the car on the ground you need a bigger force to push the wheels inwards. Think about pulling a paper under books vs without books on top of it.
with a typical 80 ftlb of torque I hope it's more than enough to overcome it.
in shop, I see people using gun to tight lug nut when car is lifted;
in car manual, it said final torque is done when car is on ground, it might indicate road side case, not in shop;
So you can only use your torque wrench as the car on the ground and ignore it.
Lug nut torque: 150 lb.ft (204 Nm) (M14 x 1.5). Torque specifications are for nut and bolt threads free of dirt and rust. Use only our recommended replacement wheel nuts and or wheel bolts. Re-torque requirement 2022 Ford Mustang Mach-E: Retighten the wheel nuts to the specified torque within 100 mi (160 km) after any wheel disturbance, such as flat tire repair, tire rotation, changing a flat tire or wheel removal.
上首页了？但我相信大部分消费者不知道这个要求。轮胎店大部分也不指出。
没几个人会花时间去翻手册的，都是大难临头才去抱佛脚, they better wish themselves luck.
https://www.amazon.com/CRAFTSMAN-Impact-Wrench-7-5-Amp-CMEF901/dp/B07QH3MBQ2
my car is old, has not TPMS, finally, I found this one $150, it works good after let shop installed on tire (replacing the tire vavles)
https://www.youtube.com/watch?v=OgLjX1Mc7m8
Never fail to check pressure regularly.
what if tire start getting flat when driving on the road?
I can feel the difference of the ride with wrong tire pressure.